Rear of a black-clad bushland home in Oyster Bay raised on round off-form concrete columns above native planting
Bushfire-Led Home Design · DA Stage

Oyster Bay Bushland Residence A BAL-FZ home on a sloping site

Oyster Bay, Sutherland Shire NSW

Project brief
Status
In progress · DA stage
Location
Oyster Bay NSW 2225
Council
Sutherland Shire Council
Type
New home
Client
Private owners
Site Area
1,001.7 m², sloping
Bushfire Attack Level
BAL-FZ (Flame Zone)
Approval Path
Development application
Designer
Francis Design, BDAA member
Services
Site ReviewConcept Design3D VisualisationBushfire DesignDA DocumentationConsultant Coordination

A home designed to float above the bush.

The Oyster Bay Bushland Residence is a new contemporary home on a 1,001.7 m² sloping bushland block in Oyster Bay, in Sydney's Sutherland Shire. The site sits in the bushfire Flame Zone (BAL-FZ), so fire protection, the slope and the neighbours' views shaped the design from the first sketch. The concept is complete and the project is now at development application (DA) stage with Sutherland Shire Council.

This home is designed not to sit heavily on the landscape, but to float above it. Round off-form concrete columns lift the main living level off the slope, so the ground below stays planted with natives and the house touches the site lightly. Concrete anchors the home to the earth, while the dark cladding and warm Corten-look battens let it recede into the trees.

The brief was a compact, minimalist home that feels connected to the bush and the water, without asking the site to be something it is not. Every decision answers one of three conditions: a Flame Zone bushfire rating, a steep block, and neighbours above and beside who value their outlook.

Street front of the Oyster Bay home with Corten-look batten screens, black cladding and a burnished concrete driveway
Street front: Corten-look battens, black metal cladding and a burnished concrete driveway on the grade.
Bushfire design

Designing for BAL-FZ in Oyster Bay bushland.

BAL-FZ is the highest of the six Bushfire Attack Levels set out in AS 3959-2018. It means a building could be in direct contact with flames from a fire front, not just embers and radiant heat. On bush fire prone land in NSW, the home must also meet Planning for Bush Fire Protection 2019.

For this house, that meant designing the fire protection into the architecture rather than adding it later:

  • Non-combustible outer skin. Matt black vertical metal batten cladding and Corten-look powdercoated battens (Dulux Duratec Weathered Steel Flat) give the warmth of timber without a combustible surface.
  • Bushfire shutters in pelmets. Shutters protect the large glazed openings from embers and radiant heat, and sit hidden in pelmets so the windows stay clear and the views open on a normal day.
  • Concrete where it matters. Off-form concrete columns, slab edges, retaining walls and stairs are non-combustible and form the structure closest to the ground, where fire and embers gather.
  • Simple roof forms. Colorbond metal roofing and low, clean roof lines reduce places for embers and leaf litter to collect.
  • Steel details. Black steel rod balustrading and steel Vergola louvred roofs keep balconies and outdoor rooms in metal.

A bushfire consultant's assessment sets the final construction requirements, and we coordinate the design with that report. See how we approach bushfire (BAL) home design.

Black metal batten cladding and steel rod balustrade above off-form concrete columns on a sloping bush site
Metal battens, steel balustrades and off-form concrete columns: a non-combustible palette for the Flame Zone.
Site

Working with the slope and sharing views in Oyster Bay.

The block falls away towards the water. Instead of cutting deep into it, the main level sits on round concrete columns, with off-form concrete retaining walls only where the house meets the ground. This limits excavation, keeps the natural fall for drainage and native planting, and lets the living areas look out through the tree canopy.

The house is compact, with low, flat roof forms that step with the land. That keeps the height down and protects the outlook of the homes above. Sutherland Shire Council assesses view impacts on neighbouring properties, so the massing was tested against their views early, using a site model and 3D views, before the design was fixed.

At the street, a burnished concrete driveway and turf-grid grass pavers handle the grade while keeping hard surfaces softer and greener. More on our approach to sloping block house design.

Site model of the BAL-FZ home on a sloping block, showing low roofs below neighbouring houses for view sharing
Site model: low, flat roofs step down the contours, below the neighbouring homes.
Comfort

Passive solar design and thermal mass.

The home is planned for passive solar performance. Exposed concrete in the structure and floors acts as thermal mass, soaking up winter sun during the day and releasing it at night, then staying cool in summer when it is shaded. The steel Vergola louvred roofs over the outdoor rooms can open for winter sun and close for summer shade and rain.

Large openings bring in daylight and cross-breezes. Inside, the bush becomes part of everyday life: light moving through the trees, water appearing between the branches. These choices also support the BASIX certificate every new NSW home needs, which sets energy, water and thermal performance targets.

Living room looking over the pool terrace and down the slope to the water at Oyster Bay
Living room: full-height glazing to the terrace, the tree canopy and the water.
Materials

Materials and why we chose them.

  • Off-form concrete

    Round columns, slab edges, retaining walls and stairs. Non-combustible structure and thermal mass that lifts the house off the slope.

  • Black metal battens

    Matt black vertical cladding. Non-combustible, and it lets the house recede into the shadows of the bush.

  • Corten-look battens

    Powdercoated in Dulux Duratec Weathered Steel Flat. A warm rust tone without rust run-off or a combustible surface.

  • Steel rod balustrading

    Fine black lines on decks and terraces that keep the views open.

  • Steel Vergola louvres

    Adjustable roofs over the outdoor rooms for sun in winter and shade in summer.

  • Bushfire shutters

    Set in pelmets over the large windows and doors. Ember and radiant heat protection, hidden when open.

  • Colorbond roofing

    A non-combustible, low-maintenance metal roof on simple roof forms.

  • Concrete and grass pavers

    A burnished concrete driveway on the grade, with turf-grid grass pavers for a greener, permeable edge.

  • Native landscaping

    Planting that belongs to the bushland setting, chosen with bushfire advice.

Stone island kitchen with timber joinery opening to a terrace and water views
Kitchen: stone island and timber joinery, opening to the terrace and the water.
Approval

The approval path: DA, bushfire assessment and BASIX.

A BAL-FZ home in NSW cannot be approved as complying development (CDC), so this house goes through a development application with Sutherland Shire Council. Under section 4.14 of the Environmental Planning and Assessment Act 1979, council must be satisfied the design meets Planning for Bush Fire Protection 2019 before it can approve it.

The DA package brings together:

  • architectural plans, elevations and sections
  • a bushfire assessment report from an accredited bushfire consultant
  • survey and, where needed, geotechnical and structural input for the slope
  • a BASIX certificate
  • a Statement of Environmental Effects covering view sharing, height, landscaping and the Sutherland Shire LEP 2015 and DCP 2015 controls
  • a landscape plan with native planting

We prepare the design and documentation and coordinate the consultants, so the owners have one point of contact through the approval.

Timber kitchen with stone splashback and island, with sheer curtains softening the light
Kitchen: timber joinery and a stone splashback, with sheer curtains to soften the light.
Status

Where the Oyster Bay project is now.

The concept design is complete and the DA is in progress. The next stage is developed design: refining details, materials and construction methods with the owners and the builder, followed by construction documentation once the DA is determined. We will update this page as the project moves forward.

Building in the Shire? See our Sutherland Shire home design page, or other local work such as the Bundeena waterfront home and Abbott Road, Heathcote.

FAQs

Building in a flame zone: questions.

What does BAL-FZ mean for a new home in Oyster Bay? +

BAL-FZ (Flame Zone) is the highest Bushfire Attack Level in AS 3959-2018. It means the home could be exposed to direct flame from a fire front. The design must use construction suited to that exposure, such as non-combustible cladding, protected openings and careful detailing, and it must meet Planning for Bush Fire Protection 2019. A bushfire consultant's report confirms the level for each site.

Can I build a new house on a BAL-FZ block using a CDC? +

No. In NSW, homes on land rated BAL-40 or BAL-FZ cannot be approved as complying development. They need a development application to council. For Oyster Bay that means a DA to Sutherland Shire Council, supported by a bushfire assessment report. Lower ratings may be able to use a CDC, subject to the other CDC rules.

Does the NSW RFS have to approve a single house in a flame zone? +

A Bush Fire Safety Authority from the NSW RFS is not required for a single dwelling. Instead, under section 4.14 of the EP&A Act, council must be satisfied the home meets Planning for Bush Fire Protection 2019. Council can consult the NSW RFS, which is more likely for higher-risk sites or where a performance solution is proposed.

What materials work for a BAL-FZ home that still looks warm? +

Non-combustible materials do the heavy lifting: off-form concrete, metal cladding, steel balustrades and metal roofing. Warmth comes from colour and texture rather than timber, for example Corten-look powdercoated battens. Large windows are protected by bushfire shutters, which can sit hidden in pelmets. Every product must be checked against the project's bushfire report.

How do you design a house on a steep Sutherland Shire block? +

Start with a contour survey, then decide how the house meets the ground. On this site the main level sits on round concrete columns with retaining walls only where needed, which limits excavation and keeps natural drainage. The driveway uses burnished concrete and grass pavers to manage the grade.

How does view sharing affect a new home design? +

When a new home could affect neighbours' views, council considers how much view is lost and how reasonable the design is. In NSW this is usually assessed using the Land and Environment Court's view sharing planning principle. Keeping the house compact, with low, flat roofs that step with the slope, helps protect the views of homes above.

Does a BAL-FZ home need a BASIX certificate? +

Yes. Every new home in NSW needs a BASIX certificate with the DA, whatever its bushfire rating. Since 1 October 2023 the thermal standard is an average of 7 NatHERS stars. Passive solar planning, thermal mass and shading, like the concrete and louvred roofs in this house, help meet the targets.

Do you design homes for bushfire-prone land across the Sutherland Shire? +

Yes. Many streets near the Royal and Heathcote National Parks and along the Georges River are mapped as bush fire prone land. We design new homes, knockdown rebuilds and extensions around the BAL rating, and coordinate the bushfire consultant, engineers and BASIX assessor.

Related concepts

Plain-English definitions in our building design glossary.

Next Step

Planning a home on a bushfire or sloping block?

Tell us about your site and we will talk you through the BAL rating, the slope and the approval path before you commit to a design.

Free Consultation

Book a Consultation

Share a little about your project and Jay will come back with a tailored next step.

Call Now Book Consult